Thermal Printer ZJ 5805 for 58mm paper roll Bluetooth 4.0 Connection with Android 4.0 for POS or Couriers
8 Item Items
In stock. It's delivered in a few hours
Warning: Last items in stock!
|2||265 Lei||Up to 530 Lei|
|4||285 Lei||Up to 1'140 Lei|
|Product type||Imprimanta termică|
|Product model||ZJ - 5805|
|Resolution||203 dpi (8 dots/mm)|
|Connections||Bluetoothm, RS-232, USB|
|Paper Feed Mode||Paper roll|
|Max paper width (mm)||58|
|Maximum roll diameter (mm)||50|
|Supply voltage (V ac)||110-240|
|Print Speed Black (mm / sec)||90|
|Product weight (kg)||0,45|
|Product Dimensions (Width x Depth x Height - cm)||7.80 x 10.60 x 5.20|
|Warranty period (months)||24|
|Warranty from release (years)||5|
Version: April 2016
• All rights reserved. It is forbidden to reproduce any part of this manual in any form without the manufacturer's express consent.
• The contents of this manual are subject to change without notice.
• Every effort has been made to ensure the accuracy of the contents of this manual at the time of its appearance. However, if errors were detected, we appreciate your help by reporting them.
• The manufacturer assumes no responsibility for the errors in this manual.
We have carefully dealt with the manual and try our best to ensure the accuracy of this manual. But we can not promise that it's always right because our products are upgraded and updated all the time. The contents of this manual will be updated without notice at any time.
All our products should be used in human-operated environments / locations. We are not responsible for any loss or damage caused by any accident while products are used without care by humans. If you experience a problem caused by inappropriate human behavior or natural disasters, we will not guarantee.
Contact your local agents for the latest product information.
This section provides important information for ensuring the printer's safety and efficiency. Read carefully.
Be sure to use the specified battery and the power supply provided by our company. Connecting to an unsuitable power source may cause fire, explosion, or damage to the printer.
Do not put the battery in fire or water, do not disassemble or change the battery, do not short-circuit it, otherwise it may cause injury or even explosion.
If the printer will not be used for a long time, be sure to remove the battery, otherwise the battery may drain the corrosive liquid, if improper operation results in leakage of the battery and the liquid is blown on the skin or clothing, please wash with water immediately if splashed In the eye, please rinse with water and see a doctor.
Please do not open the paper cover when printing, but only when printing is finished, do not touch the print head with your hand or body, overheating can cause burns.
Notes on use
1. Do not store the printer in hot or humid conditions.
2. The lithium battery has a character that, if not used for several months, can not be recharged.
3. The power adapter of the printer must be connected to a stable voltage of 110 ~ 220 Volts, please do not use other devices in the same socket to avoid voltage fluctuations.
4. Avoid water or conductive materials (eg metal). If water is present on the surface, please stop the power immediately.
5. Ensure that a roll of thermal paper is always inserted in the printer to avoid damage to the print roller and the printer head.
6. Make sure your printer is serviced and repaired by a qualified technician. There is no responsibility for incorrect use and / or for unqualified service.
7. The power adapter shipped with this printer is designed specifically for use with the printer only, do not use an improper power adapter. Use the 9V-2A standard power adapter.
8. To ensure the print quality and longevity of the printer, make sure that only good quality paper rolls are used.
9. Please keep this manual in a safe place where it can be readily accessed and used for reference.
Can print thermal paper with a width of 58 mm
Max paper diameter: 50mm
The lithium battery of high power, the standby time can reach 5-6 days
Automatic shutdown, automatic wakeup, power saving
Small size, light weight, reliable performance, easy to connect, easy to use
Compared to the traditional thermal printer, the Thermal printer ZJ 5805 has a smaller body, more stable printing and the advantages of portability. The Mini printer can work on a variety of locations, such as printing TAXI receipts, printing administrative charges, printing postcards, printing restaurant order information, online printing of payments, etc. With the growing popularity of the smartphone, Thermal printer ZJ 5805 has an assured future.
Printing Method: Direct Thermal
Speed: 90mm / sec
Reliability TPH Life: 100km
Resolution: 203 DPI (8dot / mm)
Printing Width: 48mm (384dots)
Paper width: 58 ± 01 mm
Roller diameter: φ≤50mm
Paper type: thermal paper
Power: rechargeable lithium battery, also supports NI-MH battery
Battery: 7.2VNiMh, 700mAh
Load method: external charger
Print parameters: logo download support, bar code printing support.
Bar Code Support: UPC-A / UPC-E / JAN 13 (EAN13) / JAN8 (EAN8) / CODE39 / ITF / CODABAR / CODE93 / CODE128; Two-dimensional code: QR CODE
Character size: 384 dots/line
Font A: 12 * 24 dots, 1.5 (W) * 3.0 (H) mm
Font B: 9 * 17 dots, 1.1 (W) * 2.1 (H) mm
Chinese Simplified / Traditional: 24 * 24 dots, 3.0 (W) * 3.0 (H) mm
Chinese character print: Chinese: Chinese simplified 24x24 dots. Support 18030 font library, Taiwan support and traditional HK (complex font) ANK: ANK characters
Language: support for multiple languages (Traditional Support, Korean, Japanese, etc. must be specified before purchase)
Extended Character Chart: OEM437 / OEM860 / OEM860 / OEM860 / OEM860 / OEM865 / OEM865 / OEM860 / OEM860 / OEM865 / / PT1511251 / OEM747 / WPC1257 / Vietnam / OEM864 / / Thai
Emulation: ESC / POS / STAR command
Interface: standard RS232 / USB, Bluetooth 2.0 and 4.0 (optional) / SPP or infrared / IRCOMM (optional) / Android to 4.0 operating system.
Operating systems with which it can communicate: Win200 / Win2003 / Win2000 / Win7 / WinXP / VISTA / WIN8 / LINUX
Working temperature: -10 ~ 50°C;
Humidity: 10 ~ 90%
1. RS232 (COM): RS232 standard communication protocol
2. Bluetooth 2.0 protocol for Bluetooth 2.0 standard communication
3. USB standard USB communication protocol
4. Bluetooth in two ways: General Bluetooth 2.0 / 4.0 communication protocol
RS-232 is developed in accordance with standard EIA asynchronous transmission, the specifications being as follows:
Data transmission: serial interface
Signal level: RS-232 level, logic 1: -5.4v, logic 0: + 5.4v
Hardware Flow Control: None
Baud rate: 2400pbs to 115200pbs (Users can get the current transfer rate from the printer self-test page.)
Data word length: 8 bits
Stop bit: 1bit
Serial cable: We made the special cable using a mini port like the Mini USB port that connects the printer. The following figure shows the meaning of the pins at the RS-232 Serial Interface:
The connection between the printer and the host follows the following rules:
However, the printer typically only works when receiving the data, nothing should respond to the host, then the TXD signal can be ignored and then the connection can be downloaded as follows:
Bluetooth is a patented standard for technology not used for short-range data exchange (using short-range radio transmissions in the ISM band at 2400-2480 MHz) from fixed devices and mobile, by creating personal networks (PANs).
Using the blue-core 4-Ext chipset, fully compatible with Bluetooth 2.0;
Reception signal has high sensitivity, low size, low consumption
Supports a wide variety of baud-rates: 1200bps ~ 1382400bps;
Supports the SPP standard, the maximum transfer speed is up to 3Mbit/s;
Note: The following changes can not be made by the user, they should be done at the factory by the manufacturer. So if the user wants to change these parameters, please inform the store before ordering our printers.
Edit the name - Send the character string "AT + NAMEXXXX", the result being "Okname", for example if you want to change the name to "LY58", send "AT + NAMELY58"
Edit the PIN code --- Send the character string "AT + PINXXXX", the result being "Oksetpin", for example if you want to change the PIN to "8888", send the string "AT + PIN8888" (Note: The default PIN is "1234", you can only reset your PIN to four digits.)
Delete the Bluetooth address --- Send the string "AT + CLR00", the result being "Okclear";
Change the baud rate --- Send the character string "AT + BAUDX, the result being "Ok + current baud rate ";
X represents the transfer rate code as follows:
For example, if you want to change the baud rate to 115200 bps, send the string "AT + BAUD8".
1. Turn on the printer;
2. Search Bluetooth device with host device;
3. If there are other Bluetooth devices, select the printer "LY58" (for example);
4. Enter the default match code "1234"
5. Pairing succeeds.
The printer is connected via standard Mini USB cable (included in accessories) for communication. The USB type belongs to the slave device type.
Make sure the printer is turned on and the USB cable connects to your computer for the first time. If we do not find "USB001", check if you can find "USB Print Support" at the location below: Path: My Computer - Properties - Management - Universal Serial Bus Controller), otherwise check the connection of the cable and printer.
The printer uses 58 mm thermal paper and has a lightweight paper loading. So the paper is easy to install. Paper max diameter is 50mm.
The method of installing thermal paper is as follows:
(1) Open the top cover of the printer
(2) Place thermal paper as follows:
(3) Pull off some of the paper out of the printer, then close the top cover.
(4) Pull the paper over the teeth cutter to break the excess paper.
POWER (Green light)
FEED (Red light)
The printer is on and has paper
The printer is on without paper
The printer has paper
In the normal working state, the paper feed starts when you press the 【FEED】 button and turn off when you release the 【FEED】 button.
Loading paper into the printer
Turn off the printer, then press and hold the 【FEED】 button and the power button at the same time. Wait for 2 seconds, then release the 【FEED】 button, the current setting will be printed.
Auto-test of printer
Turn off the printer, then press and hold the 【FEED】 button and press the power button at the same time. Wait until both the power indicator and the 【ERROR】 LED are both turned on, then the 【ERROR】 LED goes off, then release the 【FEED】 button, the language setting status will be printed.
Turn off the printer, then press and hold the 【ERROR】 button and press the power button at the same time. Wait until both the power indicator and the 【ERROR】 LED are both turned on and then the 【ERROR】 LED goes off after the 【ERROR】 LED releases the 【FEED】 button, the density setting will be printed. (It has three levels of print density setting, it is a low level circle → Middle level → High level → Low level ..., switch the density state by repeating the operation above.)
Set the print density
Turn off the printer, hold down the 【MODE】 button and press the power button at the same time. Wait until both the power indicator and the 【ERROR】 LED are both turned on and then the 【ERROR】 LED goes off, then release the 【MODE】 button. The printer turns into hexadecimal printing mode and prints the presentation. You can stop printing hexadecimal: The output mode of the hexadecimal printing mode is by turning off the printer.
Step 1: Make sure your device (such as your PC, Notebook) has Bluetooth, and once Bluetooth for your device is turned on, you will see the Bluetooth sign displayed at the bottom right of the device screen.
Step 2: Turn on the Bluetooth printer.
Step 3: To add the Bluetooth printer, click left on click "Add a Bluetooth device", then go to the wizard screen, choose "My device is configured and ready to be found", then click "Next".
Step 4: If you can see the screen below, then the device is looking for the Bluetooth printer, please wait
Step 5: Once you have found the Bluetooth printer you can see the list on the screen, here, for example, the Bluetooth LY58 printer has been successfully found. Click "-LY58", then click "Next"
Step 6: Choose "Let me choose my own passkey", then enter "1234" (this is the factory default access code, if you want to change it, you must let us know to set your new factory password before shipping) Then click on "Next".
Step 7: If you can see the screen below, it means that the Bluetooth printer is already connected. Please write down the assigned COM ports, then click "Finish"
(Note: The Bluetooth device will automatically assign a COM port.)
Step 8: Now if you want to test whether the printer is OK for printing, you can use a hyperterminal eg. putty and send the data to the COM outgoing port (just like the above image: COM5). (Port settings are 9600, N, 8.1)
The first thing is to connect the USB cable between the printer and the computer and turn on the printer.
The second is to find the printer driver called "setup.exe" included in the CD (or here ) and double-click it. Then you enter to the installation screen. Follow the steps in sequence:
Step 1: Select the language you want. We recommend that you choose English and then click "OK" to continuea
Step 2: Click "Next" to continue.
Step 3: Select that you agree as below and click "Next" to continue.
Step 4: Click "install" to continue.
Step 5: Select the operating system you are using, then click "Next" to continue.
Step 6: In this setup screen, just set the "Printer Port Settings" option.
Ports: Choose "USB001", then click "OK" to continue.
Step 7: Click "Continue Anyway" to continue.
Step 8: In this step, if you see the reboot option, click "No, I will restart the computer later", then click "Finish".
Step 9: The printer driver has been installed successfully so far. You will see the printer properties window (you can also open it from "printers and faxes" on the computer's control panel.)
Now, we want to check if the driver is working, click "General," then click "Print Test Page",
If the printer prints a normal page, it indicates that the driver is working well. You can use the printer right now, you do not have to read the contents below.
// ************************************************ ********* //
If the printer does not print anything and the driver displays the error message for example, port setting may be wrong
Click "Ports", try to select the other USB ports, "USB002", then click "Apply"
And then click "General" → click "Print Test Page" to try again.
If the printer prints a normal page, it indicates that the driver is working fine. You can use the printer now.
If it does not work, try changing the "USB002" port to
"USB003" or "USB004", then click "Apply" until the printer prints a normal test page.
If you tried all the USB ports and the printer does not work at all, please ask for help from the store.
When the printer has the following conditions, you need to clean the print head:
The printer does not print clearly and the thermal paper is OK.
Print length is not clear
Paper scroll noise.
The printhead cleaning steps are as follows:
1. Turn off the printer and open the paper cover. Remove the roll of thermal paper.
2. If the printer just finished printing, wait for the print head to cool.
3. With a soft cotton cloth soaked in ethanol (make sure it's not too wet), gently wipe off the thermal printer's head and remove any dust or stains.
4. Wait for complete evaporation of any traces of ethanol, put the roll of thermal paper in the printer and close the lid, then print a test page.
When the printer is up and running it must be turned off
Avoid touching the surface of the print head with your hand or other tools. Do not use tweezers to scratch the surface of the printer head and other sensitive parts.
Do not use gasoline, acetone and other organic solvents to clean the printer head.
This manual applies to all our Android-compatible printers (both the 58mm and 80mm printer)
Currently, the common communication ports we've used for the Android OS are (USB, Ethernet, Bluetooth and WiFi)
If you want to use the Android device connected to our printer, first make sure the printers can be supported by Android systems, do the following (for example Bluetooth):
- Insert CD into CD-ROM, connect mobile phone to computer
- find the file called " SDK " on the CD driver, then follow the path:
BLUETOOTHDEMO >> bin >> PrintDemo.APK, install it on your Android phone. (The default Bluetooth pairing password is "1234")
- Connect your mobile phone to the printer after the installation is completed
- Find this icon and open it. (The Ethernet interface will ask for your IP, you can get it from the self-test page), click "Connect printer" after successful connection, click "Print Test Page", The printer will work.
If you use "Ethernet", "USB" or "WIFI" communication, set "BluetoothDEMO" in "Step 2" to "NETDEMO", "USBDEMO" or "WIFIDEMO".
You can get all the original code in the path below if you need to develop your own APK file (The path is :)
Why does the printer print strange characters?
A: Ensure that the PC transfer rate setting is the same as the baud rate. (We can find the baud rate of the printer on the self-test page)
The self-test page is ok but the printer does not work after the driver is installed.
A: Check the installation again according to the installation wizard above and check that the correct port is selected
The cash drawer does not open?
A: Turn on the money drawer in the device settings and check the cable connection mode
Does paper feed no longer work?
A: Use a soft brush to clean the paper sensor and try again
Strange characters appear after a while
A: Interface board damaged.
A: Check the connection / adapter / power cable / power switch
Strange characters appear except the Arabic numerals.
A: Incorrect language, use the applications in the "Tools" folder on your CD or CD here to change the language to "ASCII".
The red LED flashes during printing.
A: Usually due to the high print head temperature. Close the printer for a while and let it cool down
Print speed is very slow for the serial printer
A: Follow this path and change the appropriate setting: Driver - Properties - Device Settings - Print Mode - Print Easy Font.
Water or other liquid spills in the printer
A: Stop the power supply immediately, dry the main board or the printer head with a hairdryer, careful at temperature (50 degree average is ok)
Reset the printer to the factory default settings.
A: Please use "Printer Tools" to reset. "Printer Tools" - "Factory Reset"
No customer reviews for the moment.